A common and expensive misunderstanding among chocolate buyers is to read “500L” on a chocolate conche machine and assume it produces 500L per day. It does not. The number on the specification sheet is the batch capacity — the volume the vessel holds in a single cycle — not the daily output. Real production capacity depends on how many batches you can complete in a day, which depends in turn on the conching time for each recipe. Confusing the two leads to machines that are either badly oversized or hopelessly too small.
Getting the calculation right before purchase is far cheaper than fixing a mismatch afterwards. This article explains the arithmetic and shows how to apply it to your own numbers.
Daily output is the product of batch capacity and batches per day:
Daily Output = Batch Capacity × Batches per Day
And batches per day depends on conching time plus cleaning and loading time:
Batches per Day = Operating Hours ÷ (Conching Time + Changeover Time)
Because conching time sits between roughly 8 and 22 hours depending on the model and recipe, the same machine can deliver very different daily outputs for different products. This is why capacity must always be calculated against a specific recipe, not against the machine label alone. A machine that easily meets demand for one recipe may fall short for a slower one.
Suppose you are considering a 500L machine and your recipe takes 12 hours to conche, with about 2 hours for unloading, cleaning and reloading, running 24 hours a day.
| Factor | Example Value |
|---|---|
| Machine batch capacity | 500 L |
| Conching time | 12 hours |
| Changeover time | 2 hours |
| Operating hours per day | 24 hours (continuous) |
| Batches per day | 24 ÷ (12 + 2) ≈ 1.7 → 1 batch |
| Realistic daily output | About 1 × 500 L per day |
In this example, a 500L machine running a 12-hour recipe completes roughly one batch per day — far less than the naive assumption of 500L per hour. If the recipe were shortened to 8 hours with the same changeover, the machine could approach two batches on a good day. The calculation, not the label, tells you what to expect.
Now compare a 1000L machine running the same 12-hour recipe with 2-hour changeover. It also completes about one batch per day, but each batch is twice the size, so realistic daily output is roughly double that of the 500L machine. This illustrates why capacity and cycle time must be considered together: doubling capacity roughly doubles output, but only if you can still complete the same number of cycles.
The most frequent errors are treating rated capacity as hourly output, ignoring changeover time, and assuming around-the-clock operation when staffed hours are actually shorter. Each of these inflates the calculated output and leads to an undersized machine. Building a realistic estimate — with honest operating hours and changeover time — protects you from a purchase you will regret within months.
Once you have a realistic daily figure, choose the standard capacity (20L, 100L, 500L, 1000L or 3000L) that meets it with a sensible margin. Confirm the machine’s refining rating (typically 20–25 μm), heating type (electric) and power supply (380V / 3 phase) as part of the same decision. A slightly larger machine that runs comfortably within its conching window is usually a safer investment than a smaller machine pushed to its limit.
Calculated output is the starting point, not the final answer. Real deliverable volume is usually slightly lower once you account for samples, start-up losses and batches held back for quality checks. Building a small contingency into your calculation keeps promises to customers realistic. It is far better to plan for a modest margin and exceed it than to promise output the machine cannot reliably deliver week after week.
It is also worth testing the figure against a real production week rather than a theoretical one. Track a few actual cycles, note where time is lost, and compare the result with your estimate. If the two differ widely, the estimate usually needs adjusting for changeover or downtime. This feedback loop, done once before purchase, is far cheaper than discovering the gap after the machine is installed.
No. 500L is the batch capacity for a single cycle. Daily output depends on conching time and changeover time. If a recipe takes 12 hours plus changeover, the machine may complete only one or two batches per day, not continuous 500L output.
Divide your operating hours by the sum of conching time and changeover time to find batches per day, then multiply by batch capacity. For example, 24 hours divided by 14 hours of cycle and changeover gives about 1.7, so one to two batches per day.
Batch capacity is the volume held in one cycle. Production capacity is the total output over a period, such as a day or week. Production capacity is always lower than batch capacity because it accounts for conching time, cleaning and downtime.
A modest margin is wise for growth, but a grossly oversized machine wastes energy, space and cleaning time when run at partial load. Base the decision on realistic calculated output, then round up to the nearest standard capacity that covers it comfortably.
Yes, dramatically. On one machine, an 8-hour recipe may allow three cycles a day while a 22-hour recipe allows only one. Always calculate output against the recipe you actually run, not a best-case figure.
A common and expensive misunderstanding among chocolate buyers is to read “500L” on a chocolate conche machine and assume it produces 500L per day. It does not. The number on the specification sheet is the batch capacity — the volume the vessel holds in a single cycle — not the daily output. Real production capacity depends on how many batches you can complete in a day, which depends in turn on the conching time for each recipe. Confusing the two leads to machines that are either badly oversized or hopelessly too small.
Getting the calculation right before purchase is far cheaper than fixing a mismatch afterwards. This article explains the arithmetic and shows how to apply it to your own numbers.
Daily output is the product of batch capacity and batches per day:
Daily Output = Batch Capacity × Batches per Day
And batches per day depends on conching time plus cleaning and loading time:
Batches per Day = Operating Hours ÷ (Conching Time + Changeover Time)
Because conching time sits between roughly 8 and 22 hours depending on the model and recipe, the same machine can deliver very different daily outputs for different products. This is why capacity must always be calculated against a specific recipe, not against the machine label alone. A machine that easily meets demand for one recipe may fall short for a slower one.
Suppose you are considering a 500L machine and your recipe takes 12 hours to conche, with about 2 hours for unloading, cleaning and reloading, running 24 hours a day.
| Factor | Example Value |
|---|---|
| Machine batch capacity | 500 L |
| Conching time | 12 hours |
| Changeover time | 2 hours |
| Operating hours per day | 24 hours (continuous) |
| Batches per day | 24 ÷ (12 + 2) ≈ 1.7 → 1 batch |
| Realistic daily output | About 1 × 500 L per day |
In this example, a 500L machine running a 12-hour recipe completes roughly one batch per day — far less than the naive assumption of 500L per hour. If the recipe were shortened to 8 hours with the same changeover, the machine could approach two batches on a good day. The calculation, not the label, tells you what to expect.
Now compare a 1000L machine running the same 12-hour recipe with 2-hour changeover. It also completes about one batch per day, but each batch is twice the size, so realistic daily output is roughly double that of the 500L machine. This illustrates why capacity and cycle time must be considered together: doubling capacity roughly doubles output, but only if you can still complete the same number of cycles.
The most frequent errors are treating rated capacity as hourly output, ignoring changeover time, and assuming around-the-clock operation when staffed hours are actually shorter. Each of these inflates the calculated output and leads to an undersized machine. Building a realistic estimate — with honest operating hours and changeover time — protects you from a purchase you will regret within months.
Once you have a realistic daily figure, choose the standard capacity (20L, 100L, 500L, 1000L or 3000L) that meets it with a sensible margin. Confirm the machine’s refining rating (typically 20–25 μm), heating type (electric) and power supply (380V / 3 phase) as part of the same decision. A slightly larger machine that runs comfortably within its conching window is usually a safer investment than a smaller machine pushed to its limit.
Calculated output is the starting point, not the final answer. Real deliverable volume is usually slightly lower once you account for samples, start-up losses and batches held back for quality checks. Building a small contingency into your calculation keeps promises to customers realistic. It is far better to plan for a modest margin and exceed it than to promise output the machine cannot reliably deliver week after week.
It is also worth testing the figure against a real production week rather than a theoretical one. Track a few actual cycles, note where time is lost, and compare the result with your estimate. If the two differ widely, the estimate usually needs adjusting for changeover or downtime. This feedback loop, done once before purchase, is far cheaper than discovering the gap after the machine is installed.
No. 500L is the batch capacity for a single cycle. Daily output depends on conching time and changeover time. If a recipe takes 12 hours plus changeover, the machine may complete only one or two batches per day, not continuous 500L output.
Divide your operating hours by the sum of conching time and changeover time to find batches per day, then multiply by batch capacity. For example, 24 hours divided by 14 hours of cycle and changeover gives about 1.7, so one to two batches per day.
Batch capacity is the volume held in one cycle. Production capacity is the total output over a period, such as a day or week. Production capacity is always lower than batch capacity because it accounts for conching time, cleaning and downtime.
A modest margin is wise for growth, but a grossly oversized machine wastes energy, space and cleaning time when run at partial load. Base the decision on realistic calculated output, then round up to the nearest standard capacity that covers it comfortably.
Yes, dramatically. On one machine, an 8-hour recipe may allow three cycles a day while a 22-hour recipe allows only one. Always calculate output against the recipe you actually run, not a best-case figure.